Onscreen Messages

The messages displayed on the LCD monitor are as follows.

Message

Description

Busy

The camera is either processing the data or writing the captured image onto the CF card. Wait until it is finished.

Loading image...

The camera is reading the image in the CF card. Wait until it is finished.

No CF card

There is no CF card. Load a proper CF card into the camera.

CF card error

There is a problem with the CF card. Replace the CF card.

CF card full

Since the CF card is full, no more images can be recorded or no more printing instructions can be saved.

No Image

The CF card has no displayable images. Either take a shot and save it or replace the CF card with one that has images.

Image too large

The image is not displayable because it is larger than 4064 x 2704 pixels.

Incompatible JPEG format

The JPEG image is not displayable because it is incompatible.

Corrupted data

The image data cannot be displayed because it is damaged.

Cannot rotate

The image cannot be rotated because it was captured by another camera, captured in a different format, or edited with a personal computer.

Unidentified Image

The image is not displayable because it was captured in an unknown format (recording format of another camera manufacturer, etc.).

Protected!

The image cannot be erased because it is erase-protected. To delete the image, first disable the erase protection.

Unselectable image

Printing of a non-JPEG image was attempted. Printing is not possible. Specification of an image captured by another camera or an image edited with a personal computer was attempted with Custom WB image selection. The white balance data cannot be loaded.

Too many marks

The printing specification was too many. The printing cannot be specified above this number.

Cannot complete!

The printing specification could not be saved.

Cannot magnify!

The image could not be magnified because it was captured by another camera or it is in an incompatible format or it has been edited with a personal computer.

Change the battery pack

There is not enough battery power for shooting or image playback. Replace the battery.

CCDRAW

The image is not displayable because it is a CCDRAW image captured by another camera.

Message

Description

Set Date/Time

The date/time has not been set. Captured images will not have the correct image capture date/time.

Turn off the camera after sensor cleaning

After cleaning the image sensor, turn the switch to <OFF>.

Battery level is too low. Cannot clean sensor

If there is insufficient battery power, the shutter may close during the cleaning of the image sensor and the shutter curtains and image sensor might be damaged. To prevent this, either use a fully-charged battery or a household power outlet before starting to clean the image sensor.

Folder number full

Keep a new CF card on hand. Since the 999Canon folder has been created, the current CF card will soon become full.

(When "IMG_9999" is created, "FULL CF" will be displayed.)

When the card photo printer for direct printing is connected to the camera, the camera's LCD monitor may display any of the messages below.

Message

Description

No paper

The paper cassette has not been inserted properly or there is no paper in the cassette. Or there is a problem with the paper feed operation.

No ink

There is no ink cassette or the ink cassette has no ink.

Incompatible paper size

The wrong-size paper has been loaded in the printer. Printing is not possible with paper of this size.

Incompatible ink size The wrong ink cassette has been loaded in the printer.

Ink cassette error

Printing is not possible with this ink cassette.

Paper and ink do not match

The paper and ink do not match each other.

Paper jam

The paper jammed during printing.

Paper has been changed

The paper size was changed prior to printing.

Recharge the printer battery

The printer's battery is exhausted.

Communication error

Communication error occurred.

Readjust trimming

Printing was attempted with a style different from the trimming setting.

Message

Description

Cannot print!

The image was captured by another camera or in an incompatible format. Or the image has been edited with a personal computer.

Could not print ** images

The image was captured by another camera or it has been edited with a personal computer and printing was attempted in accordance with the DPOF setting for ** prints.

** images remaining

Since the printing with the DPOF setting was interrupted, ** prints still remain to be printed.

Cannot trim

The image was captured by another camera or it is in an incompatible format. Or the image has been edited with a personal computer. Such images cannot be trimmed.

When a BJ printer capable oD direct printing is connected to the camera, the camera's LCD monitor may display any oD the messages below. ID any oD these messages are displayed, check the error code on the BJ printer's operation panel and refer to the BJ printer's manual Dor the error description.

Message

Description

No paper

The paper has not been inserted properly or there is no paper. Or there is a problem with the paper feed operation.

No ink

There is no ink tank or the ink tank has no ink.

Paper jam

The paper jammed during printing.

Printer in use

Printing from the personal computer or the memory card in the printer is in progress. When the printing ends, the images in the camera's CF card will start printing automatically.

Printer warming up

The printer is preparing for printing. When the printer is ready, printing will start automatically.

No printhead

There is no print head.

Printer cover open

Close the printer's front cover.

Media type error

Paper that the printer cannot use has been selected. Select a paper that can be used with the [Style] setting on the camera's direct printing screen.

Paper lever error

Set the paper spacing lever to the proper position.

Low ink level

The ink tank must be replaced soon. Keep a new ink tank on hand. To resume printing, select [Resume] on the error message screen.

tt e

Message

Description

Waste tank full

To resume printing, press the BJ printer's Reset button. Have the waste ink tank replaced by your dealer or service center (see the list that came with the BJ printer) at your earliest convenience.

Printer error

Turn off the printer and turn it back on. If the error is still displayed, consult your nearest BJ printer service center (see the service center list in the printer's manual).

Communication error An error occurred during communications. Turn off the printer and turn it back on and start printing again.

Readjust trimming

The style does not match the trimming that was set.

Cannot print!

The image was captured by another camera or in an incompatible format. Or the image has been edited with a personal computer.

Could not print ** images

The image was captured by another camera or it has been edited with a personal computer and printing was attempted according to the DPOF setting for ** prints.

** images remaining

Since the printing with the DPOF setting was interrupted, ** prints still remain to be printed.

Cannot trim

The image was captured by another camera or in an incompatible format. Or the image has been edited with a personal computer. Such images cannot be trimmed.

DIY Battery Repair

DIY Battery Repair

You can now recondition your old batteries at home and bring them back to 100 percent of their working condition. This guide will enable you to revive All NiCd batteries regardless of brand and battery volt. It will give you the required information on how to re-energize and revive your NiCd batteries through the RVD process, charging method and charging guidelines.

Get My Free Ebook


Post a comment