Image Playback

Single Image Display

1 Playback the image.

• Press the <H> button. ► The last captured image or last image viewed will appear.

Single Image Display

2 Select the image.

• To playback images starting with the last image, turn the <©> dial counterclockwise. To playback images starting with the first captured image, turn the dial clockwise.

• Press the <INF0.> button to change the display format.

3 Exit the image playback.

• Press the <H> button to exit the image playback and return the camera to shooting ready.

Shooting Information Display

Exposure compensation amount

Flash exposure— compensation amount

Aperture

Protect

— Folder number - File number CF card

Shutter speed "5

Metering mode

Shooting mode

Color temperature if <Q> is set Image-recording quality

File number/ Total images recorded

White balance

White balance correction

P GB EH-11/3 I E3100-520013 ÎEA5.G3 g?®. 0, 0. 0 ra-JL 2.20MB A S RGB 6/13B Q6/25/2C07 11:39:21-

Histogram (Brightness/RGB)

Picture Style settings

ISO speed

Color space Date and time

Original decision (image verification) data appended

File size

• About the Highlight Alert

When the [4 Highlight alert] menu is set to [Enable], overexposed highlight areas will blink. To obtain more image detail in the overexposed areas, set the exposure compensation to a negative amount and shoot again.

• About the AF Point Display

When the [4 AF point disp.] menu is set to [Enable], the AF point which achieved focus will be displayed in red. If automatic AF point selection was used, multiple AF points might be displayed in red.

• About the Histogram

The brightness histogram display shows the exposure level distribution, overall brightness, and gradation. And the RGB histogram display is for checking the color saturation and gradation. The display can be switched with the [4 Histogram] menu.

[Brightness] Display

This histogram is a graph showing the distribution of the image's brightness level. The horizontal axis indicates the brightness level (darker on the left and brighter on the right), while the vertical axis indicates how many pixels exist for each brightness level. The more pixels there are toward the left, the darker the image. And the more pixels there are toward the right, the brighter the image. If there are too many pixels on the left, the shadow detail will be lost. And if there are too many pixels on the right, the highlight detail will be lost. The gradation in-between will be reproduced. By checking the image and its brightness histogram, you can see the exposure level inclination and the overall tone reproduction condition.

[RGB] Display

This histogram is a graph showing the distribution of the image's brightness level of each primary color (RGB or red, blue, and green). The horizontal axis indicates the color's brightness level (darker on the left and brighter on the right), while the vertical axis indicates how many pixels exist for each color brightness level. The more pixels there are toward the left, the darker and less prominent the color. And the more pixels there are toward the right, the brighter and denser the color. If there are too many pixels on the left, the respective color information will be lacking. And if there are too many pixels on the right, the color will be too saturated with no detail. By checking the image's RGB histogram, you can see the color's saturation and gradation condition and white balance inclination.

Sample Histograms

T '

Dark image

P

1[

Normal image

P

Bright image

Index Display

Turn on the index display.

• During image playback, press the <HA> button.

► The 4-image index display will appear. The currently-selected image will be highlighted in a blue frame.

• Press the < HA > button again to switch to the 9-image index display.

Select the image.

• Turn the <©> dial to move the blue frame.

• To display an image, press the <U> button.

I Jump Display

You can skip over images during playback to find the image you want faster.

Browsing Through Images

During image playback, press the <JUMP> button and turn the <©> dial to select the jump method [1 image/10 images/100 images/Screen/ Date]. With the index display, you can jump by a single screen by selecting [Screen]. To jump by shooting date, select [Date].

• During image playback, turn the <6> dial.

► The jump display will proceed according to the selected jump method.

► On the bottom right, the jump method and current image location are

Image location indicated.

U/y Magnified View

Magnified area

Magnified area

Magnify the image.

• During image playback, press the <U> button to magnify the image.

• If you keep pressing the <U> button, you can magnify the image up to 10x.

• Press the <HA> button to reduce the magnification.

• Use <9> to scroll around the magnified image.

E|1 • You can turn the <6> or <Q> dial to view another image.

• Magnified view is not possible during the image review immediately after the image is taken.

Select [Rotate].

• Under the [3] tab, select [Rotate], then press <©>.

Select the image to rotate.

• Turn the <6> or <©> dial to select the image, then press <©>.

• Each time you press <©>, the image will rotate.

• To rotate another image, repeat the above procedure.

• Press the <MENU> button to return to the menu.

If the rotated image is not displayed in the rotated orientation during image playback, set the [5 Auto rotate] menu to [OnZ ■].

M Auto Playback

You can playback the CF card's images in an automatic slide show. Each image will be displayed for about 4 sec.

Select [Auto play].

• Under the [4] tab, select [Auto play], then press <©>.

► The auto play screen will appear.

Start the auto play.

► After [Loading image...] is displayed for a few seconds, auto play will start.

• During pause, [II ] will be displayed on the upper left of the image. Press <©> again to resume the auto play.

Stop the auto play.

• To stop the auto play and return to the menu, press the <MENU> button.

ES • During pause, you can turn the <Q> dial to view another image.

• During auto play, auto power off will not work.

• The display time may vary depending on the image.

Viewing the Images on TV

By connecting the camera to a TV set with the video cable (provided), you can view the captured images on a TV set. Turn off the camera and the television before connecting them.

Connect the camera to the TV.

• Open the camera's terminal cover.

• Use the video cable (provided) to connect the camera s <^ut°> video OUT terminal to the TV monitor's VIDEO IN terminal.

• Insert the video cable plugs firmly all the way.

Turn on the TV and switch the TV's line input to VIDEO IN.

Set the camera's power switch to <ON>.

Press the <H> button.

► The image will appear on the TV screen. (Nothing will be displayed on the camera's LCD monitor.)

• After you finish, set the camera's power switch to <OFF>, turn off the TV, then disconnect the video cable.

• If the video system format does not match the TV's, the image will not be displayed properly. Set the proper video system format with [6 Video system].

• Do not use any video cable other than the one provided. Images might not be displayed if you use a different video cable.

E|1 Depending on the TV monitor, part of the image might be cut off.

+1 0

Post a comment